0939 900 600
info@ldh.com.vn
YCM7YV Thiết bị đóng cắt/ Cầu dao tự động MCСB (sau đây gọi là: máy cắt mạch) phù hợp với lưới điện hạ thế có AC 50Hz, điện áp cách điện định mức 800V, điện áp hoạt động định mức 400V trở xuống và dòng điện hoạt động định mức lên đến 800A.
Máy cắt mạch có chức năng giới hạn thời gian đảo ngược trễ dài khi quá tải, giới hạn thời gian đảo ngược trễ ngắn mạch, giới hạn thời gian cố định trễ ngắn mạch, chức năng bảo vệ tức thời ngắn mạch và dưới điện áp. Trong trường hợp bình thường, máy cắt mạch được sử dụng để đóng ngắt mạch không thường xuyên và khởi động động cơ không thường xuyên.
Dòng máy cắt mạch này có chức năng cách ly
Tiêu chuẩn: IEC60947-2
General
YCM7YV series electronic plastic case circuit breaker (hereinafter referred to as: circuit breaker) is suitable for low-voltage power grids with AC 50Hz, rated insulation voltage 800V, rated operating voltage 400V and below, and rated operating current up to 800A. The circuit breaker has overload long-delay inverse time limit, short-circuit short-delay inverse time limit, short-circuit short-delay fixed time limit, short-circuit instantaneous and under-voltage protection functions. Under normal circumstances, the circuit
breaker is used for infrequent switching of circuits and infrequent starting of
motors.This series of circuit breakers has isolation function
Standard: IEC60947-2.
Operating conditions
1. Ambient air temperature
a)The upper limit value does not exceed +40℃;
b)The lower limit value does not exceed -5℃;
c)The average value over 24 hours does not exceed +35℃;
2. Altitude
The altitude of the installation site does not exceed 2000m.
3. Atmospheric conditions
The relative humidity of the atmosphere does not exceed 50% when the ambient
maximum temperature is +40°C; it can have higher relative humidity at lower
temperatures; when the monthly average minimum temperature of the wettest
month is +25°C, the monthly average maximum temperature of the month is +25°C. The relative humidity is 90%, taking into account condensation that occurs on the
product surface due to temperature changes.
4. Pollution degree
Pollution degree 3, the accessories installed in the circuit breaker have a pollution degree 2.
5. Installation category
The main circuit of the circuit breaker shall be installation category III, and the auxiliary circuit and control circuitshall be installation category II.
6. Installation conditions.
Circuit breakers should generally be installed vertically, usually with upward wiring, and the external magnetic field at the installation site should not exceed 5 times the geomagnetic field in any direction.
Function Description
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
Liên hệ
General
YCM7YV series electronic plastic case circuit breaker (hereinafter referred to as: circuit breaker) is suitable for low-voltage power grids with AC 50Hz, rated insulation voltage 800V, rated operating voltage 400V and below, and rated operating current up to 800A. The circuit breaker has overload long-delay inverse time limit, short-circuit short-delay inverse time limit, short-circuit short-delay fixed time limit, short-circuit instantaneous and under-voltage protection functions. Under normal circumstances, the circuit
breaker is used for infrequent switching of circuits and infrequent starting of
motors.This series of circuit breakers has isolation function
Standard: IEC60947-2.
Operating conditions
1. Ambient air temperature
a)The upper limit value does not exceed +40℃;
b)The lower limit value does not exceed -5℃;
c)The average value over 24 hours does not exceed +35℃;
2. Altitude
The altitude of the installation site does not exceed 2000m.
3. Atmospheric conditions
The relative humidity of the atmosphere does not exceed 50% when the ambient
maximum temperature is +40°C; it can have higher relative humidity at lower
temperatures; when the monthly average minimum temperature of the wettest
month is +25°C, the monthly average maximum temperature of the month is +25°C. The relative humidity is 90%, taking into account condensation that occurs on the
product surface due to temperature changes.
4. Pollution degree
Pollution degree 3, the accessories installed in the circuit breaker have a pollution degree 2.
5. Installation category
The main circuit of the circuit breaker shall be installation category III, and the auxiliary circuit and control circuitshall be installation category II.
6. Installation conditions.
Circuit breakers should generally be installed vertically, usually with upward wiring, and the external magnetic field at the installation site should not exceed 5 times the geomagnetic field in any direction.
Function Description